How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
Just how do you really feel on the subject of Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old bathtub and also place the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to think about employing one prior to you start. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the arrangement of your previous water pipes.
Your devices as well as product list must comprise the following:
Preparing for the Setup
To start with, the supporting framework provided with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both taps using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are valuable in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub up until the spirit level reads degree.
To mount taps, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the bath tub as well as additionally inspect the overflow outlet and also the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait until the bath tub has been used at the very least once as this will certainly settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Secure the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture an inflexible seal, triggering the water to pass through the wall between the bathroom as well as the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can fracture relatively early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our article about How to Install a Bathtub Yourself. Thanks a lot for spending some time to read through our article post. Do you know about somebody who is looking into the topic? Be sure share it. We love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Quote & Schedule Report this page